Critical Analysis of the Existing Notions of Self-regulation of Arc Welding Consumable Electrode

B.E. Paton, V.S. Sidoruk, S.Yu. Maksimov, Yu.N. Saraev

Abstract


The modern conception of the essence of the phenomenon of self-arc mechanized arc welding. Revealed some erroneous interpretation algorithm self-arc. Considered technical solutions, which are based on the phenomenon of self-regulation of the arc. The extension of the term “self-regulation process of melting of the electrode”.


Full Text:

PDF

References


Paton B.E., Maksimov S.Yu., Sidoruk V.S., Saraev Yu.N. On the issue of self-regulation of arc welding consumable electrode [K voprosu o samoregulirovanii dugi pri svarke plavyashchimsya elektrodo], Svarochnoye proizvodstvo [Welding production], 2014, no. 12, pp. 3-11. (in Russ.). DOI: 10.1080/09507116.2015.1012381

Kasprzhak G.M., Alekin L.E. The structure and method of analysis of the process of self-regulation of the arc when welding [Struktura i metodika analiza protsessa samoregulirovaniya dugi pri svarke], Sbornik trudov sektsii elektrosvarki AN SSSR: Avtomaticheskoye regulirovaniye dugovoy svarki [Proceedings of the USSR Academy of Sciences Section Electric: Automatic control of arc welding], Moscow, Academy of Sciences, 1953, is. 1, pp. 69-89. (in Russ.)

Kasprzhak G.M., Shchitova V.M. Structural classification and comparative analysis of automatic control systems [Strukturnaya klassifikatsiya i sravnitelnyy analiz sistem avtomaticheskogo regulirovaniya], Sbornik trudov sektsii elektrosvarki AN SSSR: Avtomaticheskoye regulirovaniye dugovoy svarki [Proceedings of the USSR Academy of Sciences Section Electric: Automatic control of arc welding], Moscow, Academy of Sciences, 1953, is. 1, pp. 31-56. (in Russ.)

Kasprzhak G.M., Alekin L.E. Problems in the theory of self-regulation in the welding consumable electrode [Voprosy teorii samoregulirovaniya pri svarke plavyashchimsya elektrodom], Elektrichestvo [Electricity], 1953, pp. 31-49. (in Russ.)

Saraev Yu.N. Managing the transfer of electrode metal at welding in CO2 short circuit arc gap (Review) [Upravleniye perenosom elektrodnogo metalla pri svarke v SO2 s korotkimi zamykaniyami dugovogo promezhutka (Obzor)], Avtomaticheskaya svarka [Automatic Welding], 1998, no. 12, pp. 16-23. (in Russ.)

Zhiming O.U., Yong WUANG, Masao USHIO, Manabu TANAKA. New concept for the characteristic of an arc welding power source (Report II), Trans. JWRI, 1999, vol. 28, no. 1.

Lankin Yu.N. Automatic control of the process GMAW CO2 with periodic short circuit arc gap (Review) [vtomaticheskoye upravleniye protsessom svarki plavyashchimsya elektrodom v SO2 s periodicheskimi korotkimi zamykaniyami dugovogo promezhutka (Obzor)], Avtomaticheskaya svarka [Automatic Welding], 2007, no. 1, pp. 3-10. (in Russ.)

Paton E.O. Vospominaniya. Derzhavne vidavnitstvo khudozhnoї lіteraturi [Memories. Reigning vidavnitstvo hudozhnoї lіteraturi], Kiev, 1956. (in Ukrain.)

Paton B.E. Svarochnyye golovki i pitaniye ikh tokom [Welding heads and power of current], Kiev, Ukrainian Academy of Sciences, 1947. (in Russ.)

Dyatlov V.I. Sensitivity works avtosvarochnyh heads at a constant speed wire feed [Chuvstvitelnost raboty avtosvarochnykh golovok s postoyannoy skorostyu podachi elektrodnoy provoloki], Trudy Leningradskogo politekhnicheskogo instituta im. M.I. Kalinina [Proceedings of the Leningrad Polytechnic Institute named after M.I. Kalinin], Leningrad, 1949, pp. 52-59. (in Russ.)

Paton B.E. Self-regulation of arc welding consumable electrode [Samoregulirovaniye dugi pri svarke plavyashchimsya elektrodom], Avtomaticheskaya svarka [Automatic Welding]. 1952, no. 1, pp. 38-45. (in Russ.)

Dyatlov V.I. The current-voltage characteristics of the compressed electric arc [Volt-ampernaya kharakteristika szhatoy elektricheskoy dugi], Avtomaticheskaya svarka [Automatic Welding], 1961, no. 1. (in Russ.)

Dyatlov V.I. Issledovaniye protsessa i razrabotka tekhnologii svarki pod flyusom: doklad-obobshcheniye opublikovannykh rabot na soiskaniye uchenoy stepeni doktora tekhnicheskikh nauk [The research process and the development of technology for submerged arc welding: report-synthesis of published studies on the degree of Doctor of Technical Sciences], Kiev, 1963. (in Russ.)

Paton B.E., Lebedev V.K. Elektrooborudovaniye dlya dugovoy i elektroshlakovoy svarki [Electric arc and electroslag welding], Moscow, Mechanical Engineering, 1968. (in Russ.)

Paton B.E. Tekhnologiya elektricheskoy svarki metallov i splavov plavleniyem [The technology of electric welding of metals and alloys melting], Moscow, Mechanical Engineering, 1974, 768 p. (in Russ.)

Lenivkin V.A., Kiselev D.V. Features self-melting electrode [Osobennosti samoregulirovaniya plavleniya elektroda], Vestnik DGTU [Bulletin DSTU], 2010, vol. 10, no. 1(44), pp. 95-101. (in Russ.)

Lebedev A.V. Effect of heat in the process of departing electrode samoregulirovaniya arc [Vliyaniye teplovydeleniya v vylete elektroda na protsess samoregulirovaniya dugi], Svarochnoye proizvodstvo [Welding production], 1978, no. 7, pp. 9-11. (in Russ.)

Saraev Yu.N., Shpigunova O.I Mathematical model of melting and transfer of electrode metal to systematic short circuit arc gap [Matematicheskaya model plavleniya i perenosa elektrodnogo metalla s sistematicheskimi korotkimi zamykaniyami dugovogo promezhutka], Svarochnoye proizvodstvo [Welding production], 1992, no. 6, pp. 28-31. (in Russ.). DOI: 10.1080/09507119309548493

Saraev Yu.N. Impulsnyye tekhnologicheskiye protsessy svarki i naplavki [Pulse welding procedures and welding], Novosibirsk, Nauka, 1994, 108 p. (in Russ.)

Saraev Yu.N., Krektuleva R.A., Shpigunova O.I. Computer simulation of adaptive pulse technological processes [Kompyuternoye konstruirovaniye adaptivnykh impulsnykh tekhnologicheskikh protsessov], Fizicheskaya mezomekhanika i kompyuternoye konstruirovaniye materialov [Physical mesomechanics and computer design of materials], Novosibirsk: Nauka, Siberian Publishing Company of the RAS, 1995, vol. 2, pp. 240-252. (in Russ.)

Potapevsky A.G. Svarka v zashchitnykh gazakh plavyashchimsya elektrodom. Chast 1. Svarka v aktivnykh gazakh [Gas-shielded welding consumable electrode. Part 1: Welding in active gases], Kiev, Ekotekhnologiya, 2007. (in Russ.)

Potapevsky A.G., Saraev Yu.N., Chinahov D.A. Svarka staley v zashchitnykh gazakh plavyashchimsya elektrodom. Tekhnika i tekhnologiya budushchego: monografiya [Welding of steel gas-shielded consumable electrode. Technique and technology of the future: monograph], Tomsk, Publishing house of Tomsk Polytechnic University, 2012, 208 p. (in Russ.)

Saraev Yu.N. Razrabotka i issledovaniye metodov i ustroystv stabilizatsii protsessa avtomaticheskoy svarki v uglekislom gaze korotkoy dugoy: diss. … kand. tekhn. nauk [Development and research of methods and devices for the stabilization process of automatic welding in carbon dioxide: dissertation of the PhD], Tomsk, 1982, 226 p. (in Russ.)

Saraev Yu.N. Razrabotka adaptivnykh impulsnykh tekhnologicheskikh protsessov svarki i naplavki: avtoref. dis. doktora tekhn. nauk [Development of adaptive pulse welding procedures and naplavki: thesis of the doctor of technical sciences dissertation], Moscow, 1995, 48 p. (in Russ.)

Zaruba I.I., Bargamen V.P., Andreev V.V. et al. Influence of the method limits the short circuit current on the formation of vertical and overhead welds when welding in carbon dioxide [Vliyaniye metoda ogranicheniya toka korotkogo zamykaniya na formirovaniye vertikalnykh i potolochnykh shvov pri svarke v uglekislom gaze], Avtomaticheskaya svarka [Automatic Welding], 1973, no. 4, pp. 64-67. (in Russ.)

Paton B.E., Potapevsky A.G. The method of automatic (semi-automatic), pulsed arc welding [Sposob avtomaticheskoy (poluavtomaticheskoy) impulsno-dugovoy svarki], Patent USSR 162252, 1970. (in Russ.)

Paton B.E., Potapevsky A.G., Podola N.V. Pulsed arc welding electrode melting-schimsya with software control of the process [Impulsno-dugovaya svarka plavyashchimsya elektrodom s programmnym regulirovaniyem protsessa], Avtomaticheskaya svarka [Automatic Welding],1964, no. 1, pp. 1-7. (in Russ.)

Potapevsky A.G., Livshits M.G., Kuplevatsky L.M. et al. Pulsed arc welding steel with a thickness of 0.5-0.8 mm [Impulsno-dugovaya svarka stali tolshchinoy 0,5-0,8 mm], Svarochnoye proizvodstvo [Welding production], 1980, no. 4, pp. 15-17. (in Russ.)

Dyurgerov N.G. The reduction and stabilization of the metal spraying process short arc welding [Umensheniye razbryzgivaniya metalla i stabilizatsiya protsessa svarki korotkoy dugoy], Avtomaticheskaya svarka [Automatic Welding], 1972, no. 6, pp. 48-49. (in Russ.)

Shchekin V.A., Dyurgerov N.G., Sagirov H.N. et al. Forced migration metalla modulated current during welding in carbon dioxide [Prinuditelnyy perenos metalla pri svarke modulirovannym tokom v uglekislom gaze], Svarochnoye proizvodstvo [Welding production], 1973, no. 3, pp. 23. (in Russ.)

Dyurgerov N.G. Reasons for periodic closures of the welding arc gap with the systematic short circuits [Prichiny periodicheskikh zamykaniy dugovogo promezhutka pri svarke s sistematicheskimi korotkimi zamykaniyami], Svarochnoye proizvodstvo [Welding production], 1974, no. 9, pp. 1-3. (in Russ.)

Knyazkov A.F., Saraev Yu.N., Dedyuh R.I. A method of arc welding with short arc gap closures [Sposob elektrodugovoy svarki s korotkimi zamykaniyami dugovogo promezhutka], Patent USSR 768108, 1984. (in Russ.)

Knyazkov A.F., Mazel A.G., Dedyuh R.I. et al. A method of arc welding with short arc gap closures and device for its implementation [Sposob elektrodugovoy svarki s korotkimi zamykaniyami dugovogo promezhutka i ustroystvo dlya yego osushchestvleniya ], Patent USSR 930824, 1985. (in Russ.)

Knyazkov A.F., Saraev Yu.N. Tymoshenko A.K. A method of arc welding [Sposob dugovoy svarki plavyashchimisya elektrodami], Patent USSR 951810, 1983. (in Russ.)

Knyazkov A.F., Saraev Yu.N., Tymoshenko A.K. et al. A method of arc welding with short arc gap closures and device for its implementation [Sposob elektrodugovoy svarki s korotkimi zamykaniyami dugovogo promezhutka i ustroystvo dlya yego osushchestvleniya], Patent USSR 1168367, 1985. (in Russ.)

Zaruba I.I., Saraev Yu.N., Knyazkov A.F. et al. A method of arc welding with short arc gap closures and device for its implementation [A method of arc welding with short arc gap closures and device for its implementation], Patent USSR 1310140, 1987. (in Russ.)

Saraev Yu.N. Justification of the concept of improving the safety and survivability of technical systems operated in the regions of Siberia and the Far North through the use of adaptive pulse welding technology [Obosnovaniye kontseptsii povysheniya bezopasnosti i zhivuchesti tekhnicheskikh sistem, ekspluatiruyemykh v regionakh Sibiri i Kraynego Severa, na osnove primeneniya adaptivnykh impulsnykh tekhnologiy svarki], Tyazheloye mashinostroyeniye [Heavy Engineering], 2010, no. 8, pp. 14-19. (in Russ.)

Saraev Yu.N. Experience in the development and practical application of adaptive pulse-arc welding equipment for construction and repair of main pipelines [Opyt razrabotki i prakticheskogo primeneniya adaptivnykh impulsno-dugovykh metodov svarki dlya stroitelstva i remonta magistralnykh truboprovodov], Voprosy materialovedeniya [Problems of Materials Science], 2015, no. 1, - pp. 210-219. (in Russ.)

Saraev Yu.N. Adaptive pulse-arc mechanized welding in the construction of main pipelines [Adaptivnyye impulsno-dugovyye metody mekhanizirovannoy svarki pri stroitelstve magistralnykh truboprovodov], Svarochnoye proizvodstvo [Welding production], 2002, no. 1, pp. 4-11. (in Russ.)

Saraev Yu.N. Features of development of electro-technological processes of welding and surfacing based algorithms for adaptive pulse control power mode settings // Russian Internet Journal of Industrial Engineering, 2015, vol. 3, no. 3, pp. 3-11. (in Russ.). DOI: 10.24892/RIJIE/20150301




DOI: http://dx.doi.org/10.24892/RIJIE/20150407

Refbacks

  • There are currently no refbacks.


Copyright (c) 2016 B.E. Paton, V.S. Sidoruk, S.Yu. Maksimov, Yu.N. Saraev

© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818

E-mail: indust.engineering.ru@gmail.com

Another version of the web site: http://indust-engineering.ru