The current situation and perspectives the development of wire-drawing steel wire
Abstract
This paper presents an analysis of the state of the ironware industry in Russia. Five major ironware companies represent the Russian market, the total share of about 88% of the market. Most of the wiredrawing equipment used in these enterprises were putting into operation in the 70-80 years of the last century and now requires modernization. The wiredrawing equipment is not producing commercially in Russia, so ironware companies implement a comprehensive program of modernization together the worlds largest engineering companies. The most extensive cooperation realized with the German company Ernst KOCH. The new equipment expands the opportunities for improving the technology process. Today is increasingly used rod, which was heat-treated with rolling heating. The process for descaling the oxide films and metal surfaces prior to drawing changed. In place of the drawing mill FIFO come straight-through mills. Non-regulated electric drive is changed to automatic drive. All this opens to researchers and practitioners new possibilities for activities, allows us to solve questions of increasing the efficiency of production of metal wire and raise its quality to a new level.
Full Text:
PDFReferences
http://www.rosmetiz.ru (accessed 1 September 2013).
http://www.koch-ihmert.de (accessed 1 September 2013).
http://www.mariofrigerio.com (accessed 1 September 2013).
http://www.sampsistemi.com (accessed 1 September 2013).
http://www.kieselstein-group.com (accessed 1 Septem-ber 2013).
http://www.gcrgroup.com (accessed 1 September 2013).
http://www.wiredrawingchina.com (accessed 1 Septem-ber 2013).
http://www.jiu-tai.com.tw (accessed 1 September 2013).
Haritonov V.A., Radionova L.V. Proektirovanie resursosberegayushchikh tekhnologiy proizvodstva vysokoprochnoy uglerodistoy provoloki na osnove modelirovaniya [Design of resource saving technologies of high-strength carbon wire], Magnitogorsk, 2008, 171 p.
Zyuzin V.I., Klekovkina N.A., Haritonov V.A., Radionova L.V. Resursosberezhenie v metiznom proizvodstve [Resource saving in hardware production], Magnitogorsk, 2001, 160 p.
Haritonov V.A. Formirovanie svoystv provoloki kholodnoy deformatsiey [Formation of cold deformation properties of the wire], Magnitogorsk, 2001, 127 p.
Nikiforov B.A., Haritonov V.A., Kopev A.V. Tekhnologiya volocheniya provoloki I plyushcheniya lenty [The technology of wire drawing and flattening tape], Magnitogorsk, 1999, 354 p.
RadionovA.A. Avtomatizirovannyy elektroprivod stanov dlya proizvodstva stalnoy provoloki [Automated electric drive of mills for the production of steel wire], Magnitogorsk, 2007, 311 p.
Kulesha V.A., Klekovkina N.A., Belalov H.V. Izgotovlenie vysokokachestvennykh metizov [Production of high-quality metal products], Beloretsk, 1999, 328 p.
Babich V.K., Gul Yu.P., Dolzhenkov I.E. Deformatsionnoe starenie stali [Deformation aging of steel], Moskau, 1972, 320 p.
Shakhpazov H.S., Nedoviziy I.N., Orinichev V.I. Proizvodstvo metizov [Production of metal products], Moskau, 1977, 392 p.
Yukhvez I.A. Proizvodstvo vysokoprochnoy provolochnoy armatury [Production of high-strength wire fittings], Moskau, 1973, 264 p.
Perlin I.L., Ermanok M.Z. Teoriya volocheniya [Theory of drawing], Moskau, 1971, 448 p.
Haritonov V.A., Posadskiy S.G., Radionova L.V. Analiticheskoe issledovanie temperaturnogo rezhima volocheniya uglerodistoy provoloki na mnogokratnykh stanakh [Analytical study of the temperature carbon wire during drawing on multiple mills], Moskau, VINITI, 2000, 20 p.
Haritonov V.A., Radionova L.V., Safonov E.V. Deformation aging of steel during multiple drawing [Deformatsionnoe starenie stali v processe mnogokratnogo volocheniya]. Sovremennye tekhnologii I materialovedenie [Modern technology and materials science], Magnitogorsk, 2003, pp. 263-267.
Haritonov V.A., Radionova L.V. Analiz vliyaniyav na fiziko-mekhanicheskie svoystva provoloki temperaturno-skorostnogo rezhima volocheniya [Analysis of the effect on the physical and mechanical properties of the wire temperature-speed mode of drawing], Moskau, VINITI, 1999, 24 p.
Bitkov V.V. Tekhnologiya I mashiny dlya proizvodstva provoloki [Technology and machines for the production of wire], Yekaterinburg, 2004, 344 c.
Radionova L.V., Haritonov V.A., Zyuzin V.I. New technological lubricant for drawing steel wire [Novye tekhnologicheskie smazki dlya volocheniya stalnoy provoloki]. Stal [Steel], 2001, no. 12, pp. 49-50.
Kolmogorov G.L., Orlov S.I., Shevlyakov V.Yu. Instrument dlya volocheniya [Tool for drawing], Moskau, 1992, 144 p.
Guryanov G.N. Method of calculating the optimum angle of the cone of the working dies at drawing a round solid profile [Metodika rascheta optimalnogo ugla rabochego konusa voloki pri volochenii kruglogo sploshnogo profilya]. Metallurgicheskaya I gornorudnaya promyshlennost [Metallurgical and Mining Industry], 2010, no. 6, pp. 58-60.
Sachava D.G., Ananeva S.V. Classification, causes, ways to prevent deterioration and destruction of the drawing tool [Klassifikatsiya, prichiny vozniknoveniya, sposoby predotvrashcheniya iznosa i razrusheniya volochilnogo instrumenta]. Stal [Steel], 2007, no. 3, pp. 75-76.
Danenko V.F., Kushkina E.Yu, Ivanova G.N. Investigation of the influence of geometry on the working channel dies of drawing force and service durability [Issledovaniye vliyaniya geometrii rabochego kanala volok na usiliye volocheniya i ekspluatatsionnuyu stoykost]. Izvestiya VGTU. [Bulletin of the VGTU], 2011, vol. 5, no.5, pp. 85-89.
Lo S.-W., Lu Yu.H. Wire drawing dies with prescribed variations of strain rate. Journal of materials processing technology, 2002, №123, pp. 212-218. DOI: 10.1016/S0924-0136(02)00033-X
Luis C.J., Leon J., Luri R. Comparison between finite element method and analytical methods for studying wire drawing processes. Journal of materials processing technology, 2005, no. 164-165, pp. 1218-1225. DOI: 10.1016/j.jmatprotec.2005.02.138
Rubio E.M., Camacho A.M., Sevilla L., Sebastian M.A. Calculation of the forward tension in drawing processes. Journal of Materials Processing Technology, 2005, no. 162-163, pp. 551-557. DOI: 10.1016/j.jmatprotec.2005.02.122
Muskalski Z., Wiewi?rowska S. The theoretical analysis of wire drawing process or hydrodynamic friction conditions. Metallurgical and mining industry, 2011, vol. 3, no. 7, pp. 74-78.
Fab?k R., P. Halfarov? P. Impact of drawing process parameters on uniformity of strain in spring wire. Metal, 2011, no. 18-20.
Radionov A.A., Radionova L.V. Technology production of high - strength wire with high plastic properties. Collection of Scientific Papers SWorld. “Modern directions of theoretical and applied researches '2013”. Odessa, 2013, is. 6, vol. 1, pp. 12-16.
Vydrin A.V. The development schemes of wire drawing in a roller dies [Razvitiye skhemy beskalibrovogo volocheniya provoloki v rolikovykh volokakh]. Vestnik Yuzhno-Uralskogo gosudarstvennogo universiteta. Seriya Metallurgiya [Bulletin of the South Ural State University. Series: Metallurgy], 2008, vol. 9(109), pp. 22-24.
Haritonov V.A., Manyakin A.Yu. Sravnitelnyy analiz protsessov volocheniya krugloy provoloki v monolitnoy i rolikovoy volokakh [Comparative analysis of the processes of drawing round wire in a monolithic and roller dies], Moskau, VINITI, 2003.
Tarnavskiy A.L. Effektivnost volocheniya s protivonatyazheniyem [The effectiveness of drawing with counterstrain], Moskau, 1959, 152 p.
Radionov A.A., Radionova L.V. Energy approach to the influence of countertension on drawing. Steel in Translation, 2008, vol. 38(5), pp. 358-361. DOI: 10.3103/S096709120
DOI: http://dx.doi.org/10.24892/RIJIE/20130101
Refbacks
- There are currently no refbacks.
Copyright (c) 2016 Ludmila Radionova, Andrey Radionov
© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818
E-mail: indust.engineering.ru@gmail.com
Another version of the web site: http://indust-engineering.ru