The Method of Stress State Analysis in the Crank Plane between the Necks of the Crankshaft

A. S. Kravchuk, A. I. Kravchuk, I. A. Tarasyuk

Abstract


The method of stress state analysis in the section of crankshaft crank located at the top and bottom dead points of the piston stroke, without considering additional cavities in journals (except for an oil channel) is proposed. The problem of the determining stress state in the crankshaft journal overlapping in an elastoplastic statement with considering large displacements is solved for the first time. A parametric crankshaft crank model taking into account all the geometric features of its design (including an oil channel) is built. The oil channel position considered as an example is characteristic of the first and last crankshaft cranks. Methodological comments to the proposed models based on use of ANSYS 10 ED are given. It allows engineering and design staff to understand the model, refine it in accordance with the drawings and perform optimization of the geometric parameters of the crankshaft by the durability criterion

Full Text:

PDF

References


Popyk K.G. Konstruirovanie i raschet avtomobil'nykh i traktornykh dvigateley [Design and analysis of car and tractor engines], Moscow, Vysshaya shkola, 1973, 400 p. (in Russ.)

D’yachenko N.Kh., Kharitonov B.A., Petrov V.M. et al. Konstruirovanie i raschet dvigateley vnutrennego sgoraniya [Design and analysis of internal combustion engine], Leningrad, Mashinostroenie, 1979, 392 p. (in Russ.)

Kravchuk A.S., Smalyuk A.F., Kravchuk A.I. Lektsii po ANSYS s primerami resheniya zadach: kurs lektsiy dlya stud. mekhaniko-matematicheskogo fak., obuch. po spets. 1-31 03 02 "Mekhanika (po napravleniyam)". V 5 ch. Ch. 1. Graficheskiy interfeys i komandnaya stroka. Sredstva sozdaniya geometricheskoy modeli: Elektronnaya biblioteka mekhaniki i fiziki [Lectures on ANSYS with examples of problem solving: a course of lectures for students of Mechanics and Mathematics faculty, trained. on spec. 1-31 03 02 "Mechanics (for directions)". In 5 vol. Vol. 1. Graphical interface and command line. Tools for creating a geometric model: Electronic library of mechanics and physics], Minsk, BSU, 2013, 130 p. Available at: http://elib.bsu.by/handle/123456789/43440 (accessed 1 February 2017). (in Russ.)

Kravchuk A.S., Smalyuk A.F., Kravchuk A.I. Lektsii po ANSYS s primerami resheniya zadach: kurs lektsiy dlya stud. mekhaniko-matematicheskogo fak., obuch. po spets. 1-31 03 02 "Mekhanika (po napravleniyam)". V 5 ch. Ch. 2. Sredstva otobrazheniya i redaktirovaniya geometriches-kikh komponentov tverdotel'noy modeli. Primery sozdaniya tverdotel'nykh modeley sredstvami ANSYS dlya resheniya fizicheskikh zadach: Elektronnaya biblioteka mekhaniki i fiziki [Lectures on ANSYS with examples of problem solving: a course of lectures for students of Mechanics and Mathematics faculty, trained. on spec. 1-31 03 02 "Mechanics (for directions)". In 5 vol. Vol. 2. Tools for displaying and editing geometric components of a solid model. Examples of creating solid models by ANSYS tools for solving physical problems: Electronic library of mechanics and physics], Minsk, BSU, 2013, 145 p. Available at: http://elib.bsu.by/handle/123456789/43443 (accessed 1 February 2017). (in Russ.)

Kravchuk A.S., Smalyuk A.F., Kravchuk A.I. Lektsii po ANSYS s primerami resheniya zadach: kurs lektsiy dlya stud. mekhaniko-matematicheskogo fak., obuch. po spets. 1-31 03 02 "Mekhanika (po napravleniyam)". V 5 ch. Ch. 3. Opredelenie fizicheskikh konstant materialov i konechno-elementnoe razbienie tverdotel'noy modeli. Primery vypolneniya etikh deystviy s postroennymi ranee modelyami: Elektronnaya biblioteka mekhaniki i fiziki [Lectures on ANSYS with examples of problem solving: a course of lectures for students of Mechanics and Mathematics faculty, trained. on spec. 1-31 03 02 "Mechanics (for directions)". In 5 vol. Vol. 3. Material physical constants setting and finite element meshing of a solid model. Examples of performing these actions for previously built models: Electronic library of mechanics and physics], Minsk, BSU, 2013, 193 p. Available at: http://elib.bsu.by/handle/123456789/43444 (accessed 1 February 2017). (in Russ.)

Kravchuk A.S., Smalyuk A.F., Kravchuk A.I. Lektsii po ANSYS s primerami resheniya zadach: kurs lektsiy dlya stud. mekhaniko-matematicheskogo fak., obuch. po spets. 1-31 03 02 "Mekhanika (po napravleniyam)". V 5 ch. Ch. 4. Ogranicheniya i nagruzki. Razdely Solution i General Postproc glavnogo menyu. Primery postanovki kraevykh zadach, ikh resheniya i prosmotra rezul'tatov: Elektronnaya biblioteka mekhaniki i fiziki [Lectures on ANSYS with examples of problem solving: a course of lectures for students of Mechanics and Mathematics faculty, trained. on spec. 1-31 03 02 "Mechanics (for directions)". In 5 vol. Vol. 4. Constraints and loads. Solution and General Postproc sections of main menu. Examples of boundary value problem statements, their solutions and viewing the results: Electronic library of mechanics and physics], Minsk, BSU, 2013, 118 p. Available at: http://elib.bsu.by/handle/123456789/43445 (accessed 1 February 2017). (in Russ.)




DOI: http://dx.doi.org/10.24892/RIJIE/20170203

Refbacks

  • There are currently no refbacks.


Copyright (c) 2018 A. S. Kravchuk, A. I. Kravchuk, I. A. Tarasyuk

© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818

E-mail: indust.engineering.ru@gmail.com

Another version of the web site: http://indust-engineering.ru