Temperature in Intermittent Cutting
Abstract
Full Text:
PDFReferences
Kasimov L.N., Akbarov M., Rahman-Zade A.Z. Investigation of the influence of some factors of the process of intermittent turning of viscous steels on the cutting temperature [Issledovanie vliyaniya nekotorykh faktorov protsessa preryvistogo tocheniya vyazkikh staley na temperaturu rezaniya], Optimizatsiya protsessov rezaniya zharo- i osoboprochnykh materialov [Optimization of processes for cutting heat and extra-strong materials], 1977. (in Russ.)
Reznikov A.N. Teplofizika protsessov mekhanicheskoy obrabotki materialov [Thermophysics of the processes of mechanical processing of materials], Moscow, Mechanical Engineering, 1981. (in Russ.)
Solodkov V.A. Povyshenie effektivnosti obrabotki rezaniem: kollektivnaya monografiya [Improving the efficiency of cutting: collective monograph], Moscow, Publishing house "Spectrum", 2012. (in Russ.)
Bobrov V.F., Granovsky G.I., Zorev N.N. Razvitie nauki o rezanii metallov [The development of the science of metal cutting], Moscow, Mechanical Engineering, 1967. (in Russ.)
Zorev N.N. Voprosy mekhaniki protsessa rezaniya metallov [Questions of mechanics of metal cutting process], Mjscow, Mechanical Engineering, 1956. (in Russ.)
Solodkov V.A. Temperature features of interrupted cutting and the effect of solid lubricants on them [Temperaturnye osobennosti preryvistogo rezaniya i vliyanie na nikh tverdykh smazok], Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta [Bulletin of the Volgograd State Technical University], 2013, no.7(110), pp. 48-49. (in Russ.)
Victor H., Kamme H. Standzeit und Verfanrensoptimierung beim Messer-kopffrasen, Zeitschrift fur industrielle Fertigung, 1977.
Murarka P., Hinduja S., Barrow G. Influence of strain, strain-sate and tempera-ture on the flow stress in the pzimary deformation zone in metall cutting, Int. J. Mach. Tool Des. Res., 1981, vol. 21(3-4), pp. 207-216. DOI: 10.1016/0020-7357(81)90018-4
Fokin O.V. Determination of temperature on the contact surfaces of the cutter with the shavings and the product [Opredelenie temperatury na poverkhnostyakh kontakta reztsa so struzhkoy i izdeliem], Vestnik mashinostroeniya [Herald of mechanical engineering], 1963. (in Russ.)
Platonov A.V. Intensifikatsiya tokarnoy otrezki trub posredstvom primeneniya predvaritel'nogo plazmennogo nagreva zagotovki [Intensification of turning pipe segments through the use of preliminary plasma heating of the workpiece: Ph.D. tech. sciences, Leningrad, 1989. (in Russ.)
Voevodin G.A. Zakonomernosti protsessa rezaniya staley s razlichnoy mikrostrukturoy i puti snizheniya intensivnosti iznosa tverdosplavnogo instrumenta [Regularities of the cutting process of steels with different microstructures and ways to reduce the wear rate of carbide tools: Ph.D. tech. sciences], Saratov, 1985. (in Russ.)
Berdnikov L.N. Prevention of brittle fracture of a cutting tool due to thermal load [Preduprezhdenie khrupkogo razrusheniya rezhushchego instrumenta, obuslovlennogo teplovoy nagruzkoy], Vestnik mashinostroeniya [Bulletin of mechanical engineering], 1976. (in Russ.)
Talentov N.V. Fizicheskie osnovy protsessa rezaniya, iznashivaniya i razrusheniya instrumenta [The physical basis of the cutting process, wear and tear of the tool], Moscow, Mechanical Engineering, 1992. (in Russ.)
Poduraev V.N. Rezka trudnoobrabatyvaemykh materialov [Cutting hard materials], Moscow, Higher School, 1974.
Zorev N.N. On the interaction of processes in the zone of chip formation and in the zone of contact of the front surface of the tool [O vzaimodeystvii protsessov v zone struzhkoobrazovaniya i v zone kontakta peredney poverkhnosti instrumenta], Vestnik mashinostroeniya [Herald of mechanical engineering], 1963. (in Russ.)
Solodkov V.A. The effect of exit conditions on the performance of carbide tools with intermittent cutting [Vliyanie usloviy vykhoda na rabotosposobnost' tverdosplavnogo instrumenta pri preryvistom rezanii], Izvestiya Volgogradskogo gosudarstvenno-go tekhnicheskogo universiteta [Bulletin of the Volgograd State Technical University], 2010, no. 12(72), pp. 62-65. (in Russ.)
Solodkov V.A. Chip formation and contact interaction upon exit [Struzhkoobrazovanie i kontaktnoe vzaimodeystvie pri vykhode], Izvestiya Volgogradskogo gosudarstvennogo tekhnicheskogo universiteta [Bulletin of the Volgograd State Technical University], 2014, no. 8(135), pp. 49-52. (in Russ.)
Chandrasekaran H., Nagarajan R. Tranzient strains and chip formation during tool entry, Pros. Int. Cont. Prod. Eng., 1977.
Pekelharing A.J. The Exit failure in Interrupted cutting, CIRP Ann, 1978, vol. 27(1), pp. 5-8.
Pekelharing A.J. Cutting tool damage in interrupted cutting, Wear, 1980, vol. 62, pp. 37-48. DOI: 10.1016/0043-1648(80)90035-6
DOI: http://dx.doi.org/10.24892/RIJIE/20190305
Refbacks
- There are currently no refbacks.
Copyright (c) 2020 V. A. Solodkov, S. I. Kormilitsin, P. A. Norchenko
© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818
E-mail: indust.engineering.ru@gmail.com
Another version of the web site: http://indust-engineering.ru