Mathematical Description of Main Electric Drive of Hot Plate Mill 5000

V.R. Gasiyarov, E.A. Maklakova

Abstract


The paper deals a mathematical model of the electromechanical system of rolling mill 5000 JSC «MMK». Block diagrams automation electric drive have been shown. Based on the block diagrams the mathematical model of the mechanical part of electric drive were developed and realized considering in Matlab/Simulink. The shock load transient processes of the rolling mill operating were received. The description of the electric drive as two-mass model is presented. In this case, this model can be recommended to study the influence of the load on the plate mill of hot rolling.

Full Text:

PDF

References


Voronin S.S., Usatyy D.Yu., Gasiyarov V.V., Radionov A.A. Analysis of the use of cambered roll with the roll shift system CVC to adjust the gap on the hot plate mill, Russian Internet Journal of Industrial Engineering, 2015, vol. 3, no. 1, pp. 45-49. DOI: 10.24892/RIJIE/20150108

Gasiyarov V.R., Radionov A.A. Mechatronic technological complex of hot plate mill 5000. Elektrotekhnicheskie sistemy i kompleksy [Electrical systems and complexes], 2013, no. 21, pp. 13-20.

Gasiyarov V.R. The specialized software for automated analysis of rolling energy-power parameters of hot plate mill 5000 mechatronic system at JSC “MMK”. Nauka i proizvodstvo Urala. [Urals Science and Industry], 2014, no. 10, pp. 133-135.

Maklakov A.S., Simulation of the main electric drive of the plate mill rolling stand, Russian Internet Journal of Industrial Engineering, 2014, no. 3. pp. 16-25. DOI: 10.24892/RIJIE/20140303

Karandaev A.S. Improvement of аutomatic electric drives for rolling machinery, Russian Internet Journal of Industrial Engineering, 2015, no. 1, pp. 3-15. DOI: 10.24892/RIJIE/20150101

Radionov A.A., Karyakina E.A. The research of the character of changes of torque in the mechanical part of the main drive of rolling stand plate mill 5000 by applying shock loads, Nauka i proizvodstvo Urala. [Urals Science and Industry], 2014, no. 10, pp. 126-129.

Krause P.C., Wasynczuk O., Sudhoff S.D. Analysis of electric machinery and drive systems: books in the IEEE press series on power engineering, USA, IEEE, 2002, 631 p.

Kopylov I.P. Matematicheskoe modelirovanie ehlektricheskikh mashin [The mathematical modeling of electric motors], Moscow, Graduate School, 2001, 327 p.

Karandaev A.S., Khramshin V.R., Andryushin I.YU., Golovin V.V., Shilyaev P.V. Mathematical model of electromechanical systems of stand interspace of wide-strip hot mill [Matematicheskoe modelirovanie vzaimosvyazannykh elektromekhanicheskikh sistem mezhkletevogo promezhutka shirokopolosnogo stana goryachey prokatki], Izvestiya vysshikh uchebnykh zavedeniy. Elektromekhanika. [Russian Electromechanics], 2009, no. 1, pp. 12-20.

Slezhanovskiy O.V., Datskovskiy L.V., Kuznetsov I.S. Sistemy podchinennogo regulirovaniya elektroprivodov peremennogo toka s ventilnymi preobrazovatelyami: uchebnoye posobiye [Control systems AC drives with the converter: study guide], Moscow, Energoatomizdat, 1983, 256 p.

Bortsov Yu.A. Avtomatizirovannyj elektroprivod s uprugimi svyazyami: uchebnoye posobiye [Automated electric drive with elastic ties: study guide], St. Petersburg, Energoatomizdat, 1992, 288 p.




DOI: http://dx.doi.org/10.24892/RIJEE/20150310

Refbacks

  • There are currently no refbacks.


Copyright (c) 2016 V.R. Gasiyarov, E.A. Maklakova

© Russian Internet Journal of Electrical Engineering. ISSN 2313-8742

E-mail: electrical.engineering.ru@gmail.com

Another version of the web site: http://electrical-engineering.ru