Selection of Die Geometric Parameters for the Low-Waste Hot Die-Forming with a Combined “Expansion-Extrusion” Method of Collar Flanges

L. V. Radionova, V. A. Ivanov, S. S. Strugov, V. V. Kolyshnickov

Abstract


In the course of computer modeling based on the DEFORM 3D software package, an experiment was conducted to determine the optimal parameters of the tool for the distribution-extrusion process. The simulation was performed by varying the cone angle of the knife, as well as by changing the conditions of contact friction. The satisfactory geometrical parameters of the knife cone, namely, the deflection angle (100) and the coefficient of friction (0.25), are determined. The simulation was carried out on the model of forging the collar flange 50-16-11-1-B. The definition of the above parameters will optimize the process of forming, eliminating the calibration operation

Full Text:

PDF

References


Dalsky A.M., Gavrilyuk V.S., Bukharkin L.N. et al. Tekhnologiya konstruktsionnykh materialov: uchebnoe posobie dlya vuzov [Technology of the construction materials: textbook for high school], Moscow, Mashinostroenie, 1990, 352 p. (in Russ.)

Volodin I.M., Romashov A.A. The System of Basic Principles of Designing Hot Bulk Stamping Processes and the Technologies Created on its Basis [Sistema osnovnykh printsipov proektirovaniya protsessov goryachey ob''emnoy shtampovki i sozdannye na ee osnove tekhnologii], Kuznechno-shtampovochnoe proizvodstvo [Forging and Stamping Production. Material Working by Pressure], 2008, no9, pp. 19-28. (in Russ.)

GOST 12820–80. Flantsy stal'nye ploskie privarnye na Ru ot 0,1 do 2,5 MPa (ot 1 do 25 kgs/sm2). Konstruktsiya i razmery [GOST 12820–80. Steel plane welded flanges for Pnom from 0,1 to 2,5 MPa (from 1 to 25 kgf/cm2). Design and dimensions], Moscow, IPK Izdatel’stvo Standartov, 1993, 43 p. (in Russ.)

Bakulina A.A., Tihonov I.A., Ter-Mateosyanc I.T. Review of the Russian market for pipeline valves in 2014 [Obzor rossiyskogo rynka truboprovodnoy armatury v 2014 godu], Armaturostroenie [Valve Industry], 2015, no.4, pp. 40-45. (in Russ.)

Strugov S.S., Ivanov V.A., Tarkalenko M.D. Kinematic state of the billet in the process of level hot die forming of the collar flanges according to the combined expansion and extrusion scheme [Kinematicheskoe sostoyanie zagotovki v protsesse bezuklonnoy goryachey ob''emnoy shtampovki vorotnikovykh flantsev po kombinirovannoy skheme "razdacha-vydavlivanie"], Kuznechno-shtampovochnoe proizvodstvo. Obrabotka metallov davleniem [Forging and Stamping Production. Material Working by Pressure], 2018, no.5, pp. 33-38. (in Russ.)

Kragelskiy I.V., Vinogradova I.E. Koeffitsienty treniya: cpravochnoe posobie [Friction coefficients: handbook], Moscow, Mashinostroenie, 1964, 213 p. (in Russ.)

Strugov S.S., Ivanov V.A., Sherkunov V.G. Comparison of Methods of Stress-Strain State Estimation in the Upset of a Cylindrical Workpiece, Bulletin of the South Ural State University. Ser. Metallurgy, 2016, vol. 16, no. 4, pp. 140-146. DOI: 10.14529/met160416

Storozhev M.V. Tekhnologicheskiy spravochnik po kovke i ob''emnoy shtampovke: spravochnik [Process handbook and forging and die forming: handbook], Moscow, Mashinostroenie, 1958, 643 p. (in Russ.)

Bryukhanov A.N. Kovka i ob''emnaya: spravochnik [Forging and die-forming: handbook], Moscow, Mashinostroenie, 1975, 402 p. (in Russ.)




DOI: http://dx.doi.org/10.24892/RIJIE/20180209

Refbacks

  • There are currently no refbacks.


Copyright (c) 2019 L. V. Radionova, V. A. Ivanov, S. S. Strugov, V. V. Kolyshnickov

© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818

E-mail: indust.engineering.ru@gmail.com

Another version of the web site: http://indust-engineering.ru