Fuel Pipes Coil Drawing Line Production for Diesel Engines

A. M. Antimonov, N. B. Pushkareva

Abstract


The technology and equipment for diesel engines steel fuel pipes cold rolling and coil drawing production on a self-aligning mandrel are considered.  We presented current production line scheme for the pipes production, which includes pipe-rolling drum mills, radial forging machines, thermal furnaces with a protective atmosphere, finishing lines for unwinding coils and straightening pipes, a system of conveyors and stores for transferring coils from one unit to another. A list of articles and patents containing basic information on this topic is attached

Full Text:

PDF

References


Antimonov A.M., Bersenyev A.A. Production of fuel lines for diesel engines, Steel in Translation, 2009, vol.39, pp. 267-269. DOI: 10.3103/S0967091209030206

Antimonov A.M., Sokolovsky V.I. Experience of using a self-mounted mandrel in the manufacture of steel fuel-conduit pipes [Opyt primeneniya samoustanavlivayushcheysya opravki pri izgotovlenii stal'nykh toplivoprovodnykh trub], Stal' [Steel], 1982, no.7, pp. 56-59. (in Russ.)

Tolstikov P.M., Antimonov A.M., Araptanov G.V. Bay drawing of steel top-piping pipes on a self-aligning mandrel [Bukhtovoe volochenie stal'nykh toplivoprovodnykh trub na samoustanavlivayushcheysya opravke], Stal' [Steel], 1985, no.1, pp. 56-59. (in Russ.)

Antimonov A.M., Tolstikov P.M. Equipment and technology for coil drawing of steel fuelline pipe on a self-adjusting mandrel, Metallurgist, 1984, vol. 28, pp. 434-436. DOI: 10.1007/BF00740388

Parshin V.S., Antimonov A.M., Boyarkin V.I. Calculation of a tool for drawing thick-walled pipes on a self-aligning mandrel [Raschet instrumenta dlya volocheniya tolstostennykh trub na samoustanavlivayushcheysya opravke], Tsvetnye metally [Non-ferrous metals], 1977, no.4, pp. 45-48. (in Russ.)

Antimonov A.M. Designing transitions when inserting thick-walled pipes on a self-aligning mandrel [Proektirovanie perekhodov pri volochenii tolstostennykh trub na samoustanavlivayushcheysya opravke], Izvestiya vuzov. Chernaya metallurgiya [Journal of Proceedings of the higher educational institutions. Ferrous metallurgy], 1978, no.2, pp. 25-28. (in Russ.)

Sokolovsky V.I., Polyansky S.N., Antimonov A.M. Duration of pipe cutting under alternating loading [Prodolzhitel'nost' rezki trub pri znakoperemennom nagruzhenii], Izvestiya vuzov. Chernaya metallurgiya [Journal of Proceedings of the higher educational institutions. Ferrous metallurgy], 1988, no.10, pp. 34-36. (in Russ.)

Antimonov A.M., Sokolovsky V.I., Dushkin V.M. On the evaluation of the static equilibrium of a self-aligning mandrel when drawing pipes [K otsenke staticheskogo ravnovesiya samoustanavlivayushcheysya opravki pri volochenii trub] Izvestiya vuzov. Chernaya metallurgiya [Journal of Proceedings of the higher educational institutions. Ferrous metallurgy], 1987, no.8, pp. 14-18. (in Russ.)

Antimonov A.M., Malykh E.T., Mamaev A.B. Calculation of the change in wall thickness during unwinding drawing [Raschet izmeneniya tolshchiny stenki pri bezopravochnom volochenii], Chernaya metallurgiya [Ferrous metallurgy], 1989, no.9, pp. 26-29. (in Russ.)

Antimonov A.M., Tolstikov R.M., Ukhov A.V. et al. Low-waste production technology of high-pressure pipes [Malootkhodnaya tekhnologiya proizvodstva trub vysokogo davleniya], Mashinostroitel' [Mashinostroitel], 1987, no.9, pp. 19-21. (in Russ.)

Antimonov A.M., Sobachkin V.V., Dushkin V.M. Assessment of the influence of oscillations of a self-established mandrel on the stability of pipe drawing [Otsenka vliyaniya kolebaniy samoustanavlivayushcheysya opravki na stabil'nost' volocheniya trub] Chernaya metallurgiya [Ferrous metallurgy], 1986, no.2, pp. 25-28. (in Russ.)

Antimonov A.M., Sokolovsky V.I. Sposob izgotovleniya toplivoprovodnykh trub [The method of manufacture of fuel pipes], USSR author's certificate 1210937, 1986. (in Russ.)

Antimonov A.M., Sokolovsky V.I. Samoustanavlivayushchayasya opravka dlya volocheniya trub [Self-supporting mandrel for drawing pipes], USSR author's certificate 988397, 1983. (in Russ.)

Anttimonov A.M., Sokolovsky V.I., Araptanov G.V. et al. Sposob bukhtovogo volocheniya tolstostennykh toplivoprovodnykh trub s vnutrennim diametrom ne bolee 3 mm [Method of bay drawing of thick-walled fuel pipes with an internal diameter of not more than 3 mm], USSR author's certificate 1183223, 1985. (in Russ.)

Antimonov A.M., Ukhov A.V., Timofeev V.A., Polyansky S.N. Trubovolochil'nyy baraban [Pipe Drum], USSR author's certificate 1232314, 1986. (in Russ.)

Ukhov A.V., Antimonov A.M., Araptanov G.V. Potochnaya liniya dlya bukhtovogo volocheniya trub [Production line for bay pipe drawing], USSR author's certificate 1445027, 1988. (in Russ.)

Antimonov A.M., Ukhov A.V., Timofeev V.A., Rushenbakh I.M., Tolstikov R.M., Araptanov G.V. Stan bukhtovogo volocheniya trub [Mill of the bucket pipe drawing], USSR author's certificate 1210936, 1986. (in Russ.)

Antimonov A.M., Ukhov A.V., Timofeev V.A. Tolstikov R.M., Aleshin V.A. Trubovolochil'nyy baraban [Pipe Drum], USSR author's certificate 1144740, 1985. (in Russ.)

Antimonov A.M., Mamaev A.B. Sposob opredeleniya profilya obzhimnoy chasti samoustanavlivayushcheysya opravki dlya volocheniya trub [Method for determining the profile of the crimping part of the self-aligning mandrel for drawing pipes], USSR author's certificate 1491599, 1989. (in Russ.)

Antimonov A.M., Tolstikov R.M., Aleshin V.A., Araptanov G.V., Moiseev G.P., Mamaev A.B. Ustroystvo dlya bukhtovogo volocheniya trub na samoustanavlivayushcheysya opravke [Device for coil drawing pipes on a self-aligning mandrel], USSR author's certificate 1042833, 1983. (in Russ.)




DOI: http://dx.doi.org/10.24892/RIJIE/20180309

Refbacks

  • There are currently no refbacks.


Copyright (c) 2019 A. M. Antimonov, N. B. Pushkareva

© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818

E-mail: indust.engineering.ru@gmail.com

Another version of the web site: http://indust-engineering.ru