Automated Calculation and Control of Body Wear in a Friction Pair

V. A. Saninsky, V. V. Korzin, M. A. Kononovich

Abstract


It has been established that with the same initial data of deviations of the covered and spanning surfaces of a hydraulic sliding bearing, the value of the calculated diametral clearance depends, in general, on the law of the distribution of errors. It is not always possible to guarantee the fulfillment of these errors, as a result of which destabilization of the gaps of the multi-support shaft support nodes is characterized by the relation h1min ? h2min ? h3min ? h4min.To calculate the diametrical gaps in a cylindrical hydraulic sliding bearing, a model was proposed based on the condition that the circumscribed and enveloping surfaces are made on the limiting dimensions that can be combined in an unfavorable and favorable direction of contact pairing. The obtained values of the volume of worn material with both options, showing the possibility of using automated calculation in the software tool COMPAS-3D.


Full Text:

PDF

References


Saninsky V.A. Metodologiya povysheniya zapasa tochnosti korennykh podshipnikov dizeley razmernoy mekhanicheskoy obrabotkoy i komp'yuternoy sborkoy: ucheb. posob. [Methodology of increasing the accuracy margin of the main bearings of diesel engines by dimensional machining and computer assembly], Volgograd, VSTU, 2011. (in Russ.)

Kragelsky I.V., Dobychin M.N., Kombalov V.S. Osnovy rascheta na trenie i iznos [Basics of calculation for friction and wear], Moscow, Engineering, 1977. (in Russ.)

Dementiev Yu.V. SAPR v avtomobile- i traktorostroenii [CAD in automobile and tractor construction]. Moscow, Academy, 2004, 224 p. (in Russ.)

Zuev S., Poleshchuk N. SAPR na baze AutoCAD - kak eto delaetsya [Autocad-based CAD system - how it is done], Moscow, BHV-Petersburg, 2004, 908 p. (in Russ.)

Kazennov G.G., Sokolov A.G. Osnovy postroeniya SAPR i ASTPP [Basics of building CAD and ASTPP], Moscow, Higher school, 1989, 200 p. (in Russ.)

Klimov V.E. Graficheskie sistemy SAPR [Graphic CAD systems], Moscow, Higher School, 1990, 142 p. (in Russ.)

Kureychik V.M., Glushan V.M., Shcherbakov L.I. Kombinatornye apparatnye modeli i algoritmy v SAPR [Combinatorial hardware models and algorithms in CAD], Moscow, Radio and communications, 1990, 216 p. (in Russ.)

Kureychik V.M. Matematicheskoe obespechenie konstruktorskogo i tekhnologicheskogo proektirovaniya s primeneniem SAPR [Mathematical support of design and technological design using CAD], Moscow, Radio and communications, 1990, 352 p. (in Russ.)

Latyshev P.N. Katalog SAPR. Programmy i proizvoditeli [CAD catalog. Programs and manufacturers], Moscow, Solon-Press, 2010, 718 p. (in Russ.)

Engelke U.D. Kak integrirovat' SAPR i ASTPP [How to integrate CAD and ASTPP], Moscow, Mashinostroenie, 1990, 320 p. (in Russ.)

Berliner E.M., Taratynov O.V. (2011) SAPR v mashinostroenii [CAD in mechanical engineering], Moscow, Forum, 2011, 448 p. (in Russ.)

Grover M., Zimmers E. SAPR i avtomatizatsiya proizvodstva [CAD and production automation], Moscow, Science, 1987, 528 p. (in Russ.)

Petrukhin A.V., Saninskii V.A., Moskvicheva N.P., Kochkin M.V. Automated selection of components in bearing assembly for diesel engines, Russian Engineering Research, 2015, vol.35, no.7, pp. 500-504. DOI: 10.3103/s1068798x15070175

Volosov S.S., Markov B.N., Ped E.I. Osnovy avtomatizatsii izmereniy [Basics of measurement automation], Standards Publishing, Moscow, 1974. (in Russ.)

Korzin V.V. Struynaya sistema izmereniya temperatury gazovykh sred: avtoref. dis. kand. tekhn. nauk [Aerodynamic system for measuring the temperature of gaseous media. Abstract of dissertation], Volgograd, VSTU, 2012. (in Russ.)

Korzin V.V. Theoretical analysis of the workflow of an aerodynamic pulse temperature converter [Teoreticheskiy analiz rabochego protsessa struynogo impul'snogo preobrazovatelya temperatury], Izv. VolgGTU. Ser. Progressivnye tekhnologii v mashinostroenii [J News of VolgGTU. Advanced technologies in mechanical engineering], 2007, no.3(4), pp. 46-47. (in Russ.)

Korzin V.V. Experimental studies of the aerodynamic pulse temperature converter [Eksperimental'nye issledovaniya struynogo impul'snogo preobrazovatelya temperatury], Izv. VolgGTU. Ser. Progressivnye tekhnologii v mashinostroenii [J News of VolgGTU. Advanced technologies in mechanical engineering], 2007, no.3(4), pp. 47-49. (in Russ.)

Saninsky V.A., Kononovich M.A. Podshipnikovyy uzel skol'zheniya [Bearing unit slip], A positive decision on the grant of a patent of Russia dated 10.23.2018 on application No. 2014131750 dated 09.03.2018. (in Russ.)

Denisov A.S., Denisov I.K. Analysis of methods for diagnosing connecting rod bearings and justifying the dynamic assessment of their technical condition [Analiz metodov diagnostirovaniya shatunnykh podshipnikov DVS i obosnovanie dinamicheskoy otsenki ikh tekhnicheskogo sostoyaniya], Dvigatelestroenie [J Engine building], 2004, no. 3, pp. 41-42. (in Russ.)

Mikita G.I. Computer assessment of the quality of assembly of sliding bearings of traction motors [Komp'yuternaya otsenka kachestva sborki podshipnikov skol'zheniya tyagovykh dvigateley], Sborka v mashinostroenii, priborostroenii [J Assembly in mechanical engineering, instrument making], 2004, no. 11, pp. 38-39. (in Russ.)




DOI: http://dx.doi.org/10.24892/RIJIE/20190202

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 V. A. Saninsky, V. V. Korzin, M. A. Kononovich

© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818

E-mail: indust.engineering.ru@gmail.com

Another version of the web site: http://indust-engineering.ru