Investigation of the Stress-strain State in the Deformation Zone of the Wire Depending on the Angle of the Die
Abstract
The paper presents the study as a result of establishing that the die angle reduction does not entail negative effects on the stress-strain state of the wire. It was established that the maximum stress-effective remain practically unchanged while changing the angle dies. When we reduce the angle of the die, it reduces the stress-mean and the maximum velocity – R of deformation in the wire during drawing. Studies were performed using the specialized software Deform.
Full Text:
PDFReferences
Sokolov I.A, Uralskiy V.I. Ostatochnyye napryazheniya i kachestvo metalloproduktsii [Residual stress and quality of steel], Moscow, Metallurgy Publ., 1981. 96 p.
Tulenkov K.I., Petrukhin S.I., Gayduchenko B.I. Analysis of the distribution of residual stresses in the cable wire [Analiz raspredeleniya ostatochnykh napryazheniy v kanatnoy provoloke], Izvestiya vuzov. Chernaya metallurgiya [Proceedings of the universities. Ferrous metallurgy], 1964, no. 10, pp. 98-102.
Kozlov V.T., Vysotin V.D. Residual stresses in the cable wire after drawing [Ostatochnyye napryazheniya v kanatnoy provoloke posle volocheniya], Stalnyye kanaty [Steel ropes], 1967, no. 4, pp. 302-310.
Zubov V.Ya., Krasilnikov L.A. Stresses in steel wire and relaxation [Napryazheniya v stalnoy provoloke i ikh relaksatsiya pri otpuske], Izvestiya vuzov. Chernaya metallurgiya [Proceedings of the universities. Ferrous metallurgy], 1965, no. 2, pp. 125-130.
Radionova L.V., Kharitonov V.A. Proyektirovaniye resursosberegayushchikh tekhnologiy proizvodstva vysokoprochnoy uglerodistoy provoloki na osnove modelirovaniya [Designing resource saving technologies of high carbon wire-based modeling], Magnitogorsk, MGTU Publ., 2008, 171 p.
Kharitonov V.A., Radionova L.V. Formirovaniye svoystv provoloki kholodnoy deformatsiyey: monografiya [Formation of cold deformation properties of the wire: monograph], – Magnitogorsk, MGTU Publ., 2008, 127 p.
Tomlenov A.D. Teoriya plasticheskogo deformirovaniya metallov [Theory of plastic deformation of metals], Moscow, Metallurgy Publ., 1972, 408 p.
Radionova L.V., Kharitonov V.A, Safonov Ye.V. Snizheniye neravnomernosti deformatsii po secheniyu provoloki pri volochenii v monolitnoy voloke [Reduced uneven strain on the cross section of the wire during drawing to a monolithic portage], Moscow, VINITI, 2001, 34 p.
Zyuzin V.I., Klekovkina N.A., Kharitonov V.A., Barykin N.P., Baryshev S.A., Gallyamov E.F., Dudin D.A., Dudina L.A., Yevteev Ye.A., Ishbayeva L.M., Ishbayeva L.M., Kalugina T.F., Klekovkin A.A., Kulesha V.A., Neznayeva N.M., Petrov V.P., Pokachalov V.V., Portsman Yu.N., Radionova L.V., Radionov A.A., Reus V.A., Rolshchikov L.D., Savelyev Ye.V., Semenov V.I., Solovyev S.E., Stolyarov A.Yu., Stukalov V.V., Khismatullin A.N., Gun G.S. Resursosberezheniye v metiznom proiz-vodstve: kollektivnaya monografiya [Resource saving in hardware production: collective monograph], Magnitogorsk, MGTU Publ., 2001, 163 p.
Radionova L.V. Razrabotka tekhnologii proizvodstva vysokoprochnoy provoloki s povyshennymi plasticheskimi svoystvami iz uglerodistykh staley: dis. kand. tekhn. nauk [Development of technology for production of high-strength wire with increased plastic properties of carbon steels: the dissertation of the PhD], Magnitogorsk, 2001, 137 p.
Radionova L.V., RadionovA.A. The current situation and perspectives the development of drawing production a steel wire, Russian Internet Journal of Industrial Engineering, 2013, no.1, pp.3-11. DOI: 10.24892/RIJIE/20130101
http://www.tesis.com.ru (accessed 20 July 2014).
Radionova L.V. Analytical studies of the influence of process parameters on the rate of deformation at high-speed wire drawing, Russian Internet Journal of Industrial Engineering, 2014, no.1, pp. 28-33. DOI: 10.24892/RIJIE/20140103
DOI: http://dx.doi.org/10.24892/RIJIE/20140204
Refbacks
- There are currently no refbacks.
Copyright (c) 2016 L.V. Radionova, V.A. Ivanov, V.S. Shatalov
© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818
E-mail: indust.engineering.ru@gmail.com
Another version of the web site: http://indust-engineering.ru