Technological Assurance of Wear Resistance of Surface Layer of Machine Parts AfterTurning

V.F. Bezjazychnyj, M.A. Prokofiev, A.N. Sutyagin

Abstract


The article describes problem of friction unit surface layer parts wear resistance assurance based on control of geometrical and physic mechanical properties to be formed the machining. The researches of stored energy of deformation in the surface layer of the sample after turning are presented. Correlation wear rate with equilibrium parameters of roughness and degree of work hardening of the surface layer of machine parts based on thermodynamic approach is obtained. The analysis of the results of the calculated and experimental determination of the wear rate of the samples of steel 45 under the conditions of the equilibrium state of the surface layer is shown. The correlation stored energy of the surface layer of machined part with the parameters of the degree of work hardening and dislocation density is obtained. Equations for calculation of roughness parameter and degree of work hardening based on correlation with machining conditions are shown.

Full Text:

PDF

References


Kombalov V.S. Ocenka tribotehnicheskih svojstv kon-taktirujushhih poverhnostej [Evaluation of tribological prop-erties of contacting surfaces], Nauka, Moscow, 1983, 213 p.

Suslov A.G. Technologicheskoe obespechenie par-ametrov sostoyaniya poverchnostnogo sloya [Technological assurance of surface layer quality parameters], Mashi-nostroenie, Moscow, 1987, 208 p.

Suslov A.G., Dalsky A.M. Nauchnye osnovy tehnologii mashinostroenija [Scientific Basis of Mechanical Engineer-ing], Mashinostroenie, Moscow, 2002, 684 p.

Bezjazychnyj V.F., Drapkin B.M., Prokofiev M.A., Timofeev M.V. Research of stored energy of deformation by metal during indentation by sphere indenter [Issledovanie zapasennoi metallom energii deformatsii pri vdavlianii charovogo indentora], Zavodskaya labortoriya. Diagnostika materialov [Factory laboratory. Material diagnostics], 2005, no.4, t.71, pp.32-35.

Trefilov V.I., Milman V.U., Firstov S.A. Phizicheskie os-novy prochnosty tugoplavkih metallov [The physical founda-tions of the strength of refractory metals, Kiev, Naukova dumka, 1975, 315 p.

Totai A.V. Phizicheskie aspekty obespecheniya us-talostnoy prochnosti detalei mashin [Physical aspects of fa-tigue strength of machine parts], Spravochnik. Ingenernyi jurnal [Handbook. An Engineering Journal], 2002, no. 8 (185), pp. 20-21.

Starkov V.K. Dislokatsionnye predstavleniya o rezanii metallov [Dislocation representations about metal cutting], Mashinostroenie, Moscow, 1979, 160 p.

Kashcheev V. N. Processy v zone friktcionnogo kon-takta metallov [Processes in the area of frictional contact metals], Mashinostroenie, Moscow, 1978, 213 p.

Russian State Standard 27674-88. Trenie, iznashivanie i smazka. Terminy i opredelenija [Friction, wear and lubrica-tion. Terms and definitions], Moscow, Publishing company of State Standards, 1988, 21 p.

Bezjazychnyj V.F. Metod podobija v tehnologii mash-inostroenija [Method of Similarity in mechanical engineer-ing], Mashinostroenie, Moscow, 2012, 320 p.




DOI: http://dx.doi.org/10.24892/RIJIE/20140408

Refbacks

  • There are currently no refbacks.


Copyright (c) 2016 V.F. Bezjazychnyj, M.A. Prokofiev, A.N. Sutyagin

© Russian Internet Journal of Industrial Engineering. ISSN 2310-0818

E-mail: indust.engineering.ru@gmail.com

Another version of the web site: http://indust-engineering.ru